|
 |
Auger Bits are designed for boring holes
in wood. They are available in several styles for various applications.
Auger bits have the following six common design characteristics: the
screw point, outlining spur, cutting edges, side lip cutter, flute,
and shank. The screw point is at the tip of bit and it provides hole
location and self feeds bit into wood. The outlining spur cuts outline
of hole and helps bit stay straight in hole. The cutting edges act
like horizontal cutter and chip out wood in the hole. The side lip
cutters act like vertical cutters and shave the sides of hole. The
flute or twist ejects the wood chips away from the cutter. The shank
may be taper square, hexagon, or round depending upon what use is was
designed for. |
|
|
|
| |
AUGER BITS
|
Auger Bits - Solid
Center
Solid Center Auger Bits are designed for
use in a hand bit brace and may be used for all general purpose boring
in soft or hard woods. Polished finish, single flute design
with double cutters, two outlining spurs, and a self feeding medium
fast pitch screw point.
Dual Auger Bits - Hex
Shank
Hex Shank Dual Auger Bits are for speedy and accurate boring in
soft and hard woods. Usable with hand braces and
"3/8" or larger electric drills. Single flute design with
single cutter, an outlining spur, and a self feeding fast pitch screw
point.
Electrician's Power
Auger Bits
Electrician's Power Auger Bits are made of special Tool Steel.
Black-oxided flutes. Three flats on shank, one
"flat" has two recesses for set screws, for use with extensions.
Double twist design with a single cutter, an outlining spur, and
a self feeding medium fast pitch screw point. Specifically designed
to fit in between building studs for the installation of conduit
and wire. Ideal for use with angle power drills.
Pipe Auger Bits
Pipe Auger Bits are made of special Tool Steel. Black oxided flutes.
Double twist design with extended lip double cutters, two outlining
spurs, and a self feeding medium fast pitch screw point. Specifically
designed for boring holes where a smooth finish is required. Ideal
for plumbing, heating, and air-conditioning.
Timber Auger Bits - 3 Flat 1/2" Shank
Timber Auger Bits with 3 Flat 1/2" Shank are designed for use with a standard rotary drill motor for drilling wooden
railway cross ties, pressure treated lumber, creosoted poles, heavy timber, bulkheads, trees, etc. Double flute design
with extended lip double cutters, two outlining spurs, and a self-feeding screw point for boring clean holes. They are
used by log home builders, arborists, railway maintenence departments, dock builders, utilities, etc.
Timber Auger Bits - 7/16" Quick Change Hex Shank
Timber Auger Bits with 7/16" Quick Change Hex Shank are designed for use with pneumatic, electric and hydraulic drill motors and impact wrenches for drilling wooden railway cross ties, pressure treated lumber, creosoted poles,
heavy timber, bulkheads, trees, etc. Double flute design with extended lip double cutters, two outlining spurs, and a
self-feeding screw point for boring clean holes. They are used by log home builders, arborists, railway maintenence
departments, dock builders, utilities, etc.
|
|
|
IMPACT WRENCH AUGER BITS
|
Impact Wrench Auger Bits - 18" Length
Impact Wrench Auger Bits are designed to
bore holes in telephone or power line poles quickly using quick change
chuck impact drills. Two sizes of shanks fit all impact wrenches
with standard 7/16" or 5/8" hex adapters. Single flute
design with single cutter, side lip, and a self feeding medium fast
pitch screw point.
Impact
Wrench Auger Bits - Carbide Tipped
Carbide Tipped Impact Wrench Auger Bits are
designed to bore holes into the hardest wood and creasoted poles
used by utilities. They will outlast and outperform tool steel
auger bits. Two sizes of shanks fit all impact wrenches with
standard 7/16" or
5/8" hex adapters. Single flute design with single cutter, side
lip, and a self feeding medium fast pitch screw point. |
|
|
SHIP AUGER BITS
|
Ship
Auger Bits - 6" Length - General Purpose
Ship Auger Bits are made of special tool steel. Machine ground hollows
with deep open throat for fast chip removal. Ideal for heavy timbers
and power poles. Single flute design with single cutter, an outlining
spur, side lip, and a self feeding medium fast pitch screw point.
Ship
Auger Bits - 17" Length - General Purpose
Ship Auger Bits are made of special tool steel. Machine ground hollows
with deep open throat for fast chip removal. Ideal for heavy timbers
and power poles. Single flute design with single cutter, an outlining
spur, side lip, and a self feeding medium fast pitch screw point.
Ship
Auger Bits - 36" Length - Special Purpose
These Ship Auger Bits are used by contractors to build
wooden retaining walls. They are
manufactured 1/16" larger than the size of threaded rod being used to anchor wooden
ties in place, e.g., a 3/4" threaded rod would use a 13/16" auger
bit.
Ship Auger Bits - 8" Length - Heavy Duty
Heavy Duty Ship Auger Bits are made of premium tool
steel. Machine ground hollows with deep
open throat for fast chip removal. Ideal for heavy timbers and power
poles. Single flute design with single cutter, an outlining spur,
side lip, and a self-feeding medium fast pitch screw point.
Ship
Auger Bits - 18" Length - Heavy Duty
Heavy Duty Ship Auger Bits are made of premium tool
steel. Machine ground hollows with deep
open throat for fast chip removal. Ideal for heavy timbers and power
poles. Single flute design with single cutter, an outlining spur,
side lip, and a self-feeding medium fast pitch screw point. |
|
|
POWER POLE BITS
|
Power
Pole Bits - 23" Length Hex Shank
Power Pole Bits are for boring creosoted poles, railroad ties, heavy
timber, bulkheads, etc. Single flute design with single cutter, an outlining
spur, side lip, and a self feeding medium fast pitch screw point. |
|
|
GIMLETS
|
Gimlet
Gimlets are a quality hand tool for boring in soft or hard
woods. Sharp screw tip bites into
wood. |
|
|
AUGER SPADE BITS
|
Auger Spade Bits
Auger Spade Bits are designed
to cut three times faster than a spade bit and do the work of an
auger bit at half the cost. Ideal for overhead work, rewiring,
running pipe, conduit, and more. |
|
|
|
|
| |
|
Copyright
© 1994-2009 by ICS Cutting Tools, Inc. All rights reserved.
No part of this page may be reproduced by any mechanical, photographic,
or electronic process, or in the form of a phonographic or
digital recording, nor may it be stored in a retrieval system,
transmitted, or otherwise copied for public or private use
without written permission of the publisher.
|
|
